Final Project/Dissertation

Permanent URI for this collection

https://testir.kiu.ac.ug/handle/20.500.12306/2230

Browse

Recent Submissions

Now showing 1 - 5 of 45
  • Thumbnail Image
    Item
    Project of an Electric Siren Circuit
    (Kampala International University, School of Engineering and Applied Sciences, Department of Electrical Engineering, 2023-03) Elsadig, Khalil Khamis Bobo
    Development of clap switch for devices is a difficult task which requires a good knowledge in electronics. As this is a complex project, special scope of work is yet to be determined so that the main objective and goal can be achieved
  • Thumbnail Image
    Item
    Design and Application of Wireless E-Menu Restaurant Ordering System
    (Kampala International University,School of Engineering and Applied Science,Department of Electrical, Telecommunication & Computer Engineering, 2022-03) Aliaa Adam Elaze Gibreell
    Automation plays a very important role in every field of human life. This project presents a simple design and implementation of a Wireless E-menu Restaurant Ordering System in which the traditional paper-based menu is replaced by a user friendly Matrix keypad-based menu. The system has Atmega 328P microcontroller which is interfaced with the input and output modules. The input module is the matrix keypad sensor which is placed on LCD (Graphical Liquid Crystal Display) to have a graphic image display, which takes the input from the user and provides the same information to the microcontroller. The output module is a RF TX module which is used for communication between the system at the customers’ table (transmitter section) and system for receiving section. Microcontroller also displays the menu items on the LCD. At the receiving end the selected items will be displayed on the LCD and by using the conveyer belt the received order will be sent to the particular table. The overview of this report is as follows: Chapter one-Introduction: It gives a brief introduction and background of the project. Chapter two-Literature review: It gives an overview of the existing technologies and devices used. Chapter three-Methodology: It explains the system design i.e. architecture and interfacing of the devices used. Chapter four-Results and discussion: Describes the results and output of the system. Chapter five-Conclusions and Future Scope: It gives the conclusions drawn from the project and brief ideas about future development works that can be undertaken. Finally, references and appendices.
  • Thumbnail Image
    Item
    Project of Automatic Load Monitoring System.
    (Kampala International University, School of engineering and applied science, 2021-11) Mohammed, Ali Osman Elnour
  • Thumbnail Image
    Item
    Design and Implementation of a four-dimensional automatic accident avoidance system
    (Kampala International University, School of Engineering and Applied Sciences, 2018-09) Isaac, Mure; Daniel, Rwotolara
    This report contains five chapters, in chapter one, as an introductory part of this project report, contained in chapter, we first define what accident is, the background of the study, that is to say, how the problem started or what prompted us to carry out the project. the problem statement, this is about the challenges we are solving, the main objective, specific objectives, significance of the study, and scope of the study. in chapter two, this chapter covers the literature review; here we look at the existing technology. this chapter also contains the history of the project, and the components used. in chapter three, it entirely covers the methodology, circuit diagram, block diagram, flow chart. chapter four. this chapter entails the system analysis and the design of the project prototype. it also includes the results from the system design process. in chapter five, it is majorly the conclusion and recommendation. also, in this chapter we look at the further research on this project, and finally the references we used and the appendix.
  • Thumbnail Image
    Item
    Password based security gate system powered by hybrid power supply with solar charging system
    (Kampala International University, School of Engineering and Applied Sciences, 2018-09) Sadiq, Iya Ahmad
    Automatic gate is one of most usefully thing to use in companies, colonies, collages, homes, and schools. There is some type to operate a gate such as a sliding on screw or on rack and pinion, piston operated, rotary. Design is available for some type of operation and it is most costly also When installation and maintenance cost is not yet been considered. The main objective of this Project is to study, analyze, and provide an enhanced design and performance of power supply, and also use it to power the automatic gate system. There are different types of mechanism used to operate gate. Those methods are finite element modeling and mechanical design concept and theories. In this system, the microcontroller is programmed with a default password. Whenever the right password is entered using 4x4 keypad. The microcontroller will give command to motor driver, and DC motor will open and close after some seconds. At the same time, LCD display the Situation, red LED shows the gate is closed, green LED shows the password is correct. In addition to this, a push button is added so that you can press it when you are coming out, you don’t need to password again. The power supply is of two types, hybrid. There is AC main power stepped down from 220V to l2V. The DC power is from rechargeable battery, recharged by a lOW solar panel. The work was successful. It is evidence that the use MCU with the right circuitry can be used to operate a security system, and the project was effective to give maximum security. So, the implementation rate is inexpensive and it is reasonable by a common person. Hence it can be afforded to purchase such security gate system to keep your property safe without any worries. I also recommend to improve on this project by adding other features like, using Bluetooth signal or remote signal. It can also be a finger print module. Lastly, I give my further research about the 1 2V rechargeable battery, the circuit needs 9V battery to be connected together with the AC supply. So, my recommendation of further research is to improve on this circuit so that you can be able to step the 1 2V battery to 9V